Tuesday, August 19, 2014

IRCC4 Layer 1b-Yellow Petticoat!

I'm using 100% linen fabric that is about 58" wide. I am also continuing my experiments with using less fabric so this petticoat is...frugal. So frugal that in the past I would have called it skimpy! My waist-to-floor measurement is 42" in front and 44" in back. Since I want a petticoat that doesn't touch the floor I cut two panels, one of each length, for my front and back skirt. I wanted a smoother-fitting front to my petticoat and a fuller hem so I cut triangles from the side edges of the front panel -- 10" wide at the waist narrowing to 0.0" at the hem -- reversed them and attached them to the back panel.

I like to stitch my angled pieces bias to straight grain (or cut edge to selvedge) to control the tendency to stretch along the seam. As you can see, I offset the triangles a bit at the bottom edge so that the long sides would be the same length when I trimmed them for hemming.


I folded back a 3/4" turn at the hem, just eyeballing the curve at the inset triangles...


pinned and basted...


and trimmed the excess.


I'm contiuing my experiments with a lightly padded version of a doppia (padded hemline) so I cut three 6" deep strips across the width of the fabric and set them edge to edge with my cut fabric at the skirt hem and basted them in place, making sure to gives some extra fabric for wiggle room at the curves of the hem.


I attached the individual pieces finished edge to finished edge in the same manner as the side seams.


To pad the hem I knew I wanted to fold my 6" strip three times. I  tried folding and measuring to see what worked best and discovered that I needed my upper line of stiching to be 2 1/8" from the hem edge so I stitched that all the way around the skirt.



Then fingerpressed down form the stich line and folded the hem in. Once...


and then twice.


As you can see the edges are *just* shy of matching on the outside...


and inside.


To make the waistband I took two lengths of cotton ribbon from my stash (they came wrapped around some pillows I bought but were too nice to throw away, even with the bright yellow printing!) marked the center point and measured out 13 inches on each side of the center point. That will give me 26" per side (front and back) and exactly enough to fit my 52" waist. since the two sides will tie on independently the waist is extreemly flexible in sizing. The pieces simply overlap! :)


While I did run a single gathering thread on the front side I didn't find it particularly useful so I simply pinned the back half in place. for both side I useed the classic method of pinning the center and outer points, foldign the remining fabric in half and pinning the new center point of the skit to the new center point of the wiast, over and over....


Since I removed fabric from the front panel and added it to the back, my front waist is only slightly gathered but the back waist has little knife pleats. I basted both waist in place with two rows of stitching and then tried on the Petticoat.


And it fit! I split my remaining piece of 6" wide fabrice (left over from the hem) into two 3" strips and finished the front and back waist bands.


Wednesday, August 13, 2014

Just a little something for the sewing kit...

All the hand sewing I have been doing for the IRCC4 has pointed out, yet again, that I need beeswax for thread in my sewing kit. As it happens I recently purchased a vintage compact case with a damascene lid with an idea of making it into a wax holder so last weekend I tracked down beeswax at my local fabric store. After removing the wax pellet from the horrible plastic case I realized that I was going to have to melt it to get it to fit into/fill the case. But how to melt a couple of tablespoons of beeswax?

I imagine that sitting it in the sun would work, but since it was evening and all I went with putting it in the case on the top of the stove near the oven vent and baking something for dinner. It worked!

I completely love it that damascene is a medieval technique which is still practiced and pretty easily available. My new wax holder? Not perfectly period...but not bad! :)